1600W Hot Air Heat Gun

Model NO.: HAG1600
Voltage: 230V
Power: 1600W
Air Flow: 180L/Min
Air Pressure: 2600PA
Weight: 1.5kg
Trademark: SUDA
Transport Package: Carton Boxes
Specification: 1 carton/set
Origin: Jiangsu
HS Code: 8515290000
1600w Hot air Heat Gun
1600/3400W    HEAT GUN
 
This heat gun series are sort of a new style manual hot air welding tools which on top of technology and got CE certificate This heat guns is double insulation, constant temperature controlled and continuously adjustable. It is suitable for welding hot plastic material like PVC ,PP,PE, PVDF, EVA,ECB,TPO ,and so on, It is also used for thermos forming, shrinking, drying, igniting operation.
 
Please read operating instructions carefully before use and keep it for further reference.
Application
Welding of thermoplastic materials as well as single-ply flexible plastics and modified bitumen in the form of boards, tubes, profiles, lining membranes, coated materials, films, foams, tiles and sheets. Main welding ways: overlap welding, welding with rod/ tape, butt welding and melt welding.
For foaming, ending and sealing of the thermoplastic semi-finished materials and plastic granules.
Drying of water-damp surfaces.
Shrinking of heat-shrink sleeves, films, tapes, solder sleeves, preformed and mould part.
Soldering of copper pipes, solder joints and metal foils.
Defrosting of frozen water pipes.
Activating and dissolving of solvent free adhesive and fusion adhesives
Igniting of wood shavings, paper, coal or straw in furnaces
 
Parameter
 
Parameter 1600W 3400W
Voltage 230V 230V
Frequency 50/60Hz 50/60Hz
Power 1600W 3400W
Adjustable Temp 20-650ºC 20-650ºC
Air flow 180L/min 360L/min
Air Pressure 2600Pa 3200Pa
Noise ≤65db ≤65db
Weight 1.5Kg 1.5Kg
 
Structure Name Of Heat Guns

  Power wire        5.  Air filters
Power switch     6. Non-slip rubber ring
Temperature Set          7. Heating elements cover
Handle
Operating Instruction
Readiness of working
Fit appropriate nozzle as required
Connect tool to the power
Adjust air temperature
Switch on then use after 5 minutes.
Operation
Do welding test in accordance with national laws and regulations or the material manufacturer's welding specifications
Check the consequence of welding test
Set welding temperature as need
Knob the temperature to zero point after use, cold airing a few minutes to cool down completely, then turn the power off and keep them well
 
Nozzles/Knob/Temperature form
Nozzle Knob Actual Temp
None 9 650ºC
Tubular nozzle 6 650ºC
20mm wide shot nozzle 8 650ºC
40mm wide shot nozzle 9 650ºC
Speed nozzle(round) 6 650ºC
Speed nozzle(triangle) 6 650ºC
Tracking nozzle 6 650ºC
 
   3) Nozzles changeable
 
Do use tools to take them off after the nozzles cooling down completely
Do not touch the hot nozzle and make sure to place it on a heat resistant surface, because of the fire hazard..
Put the nozzle on the heater tube and secure the nozzle by the screw on the cap.
 
    4) Maintenance
 
Clean polluted air filter with a small brush or replace it
Clean welding nozzle with a steel brush.
Check mains cable and plug for electrical and mechanical damage.
      Caution:
The voltage rating stated on the tool must correspond to line/mains voltage.
 For personal protecting on the building site, we strongly recommend the tool be connected to a GFCI (Ground Fault Circuit Interrupter) or a RCCB (Residual Current Circuit Breaker)
The tool much be operated with supervision. Heat can reach combustible materials which are out of sight.
                       Protect tools from damp and wet
 

Arch Balloon Kit

Arch Balloon Kit,Balloon Arch Stand,Diy Balloon Arch Kit,Balloon Garland Arch

NINGBO ART TALK CRAFTS CO LTD , https://www.just-arts-crafts.com

Posted on